Anti glare passage lamp use method and precautions analysis
Anti-glare passage lamps are developed and manufactured to meet the lighting characteristics and needs of railway tunnels, highways, power, metallurgy, petroleum and petrochemical and various plant areas, workshops, bridges, stations, squares and large facilities, stadiums, etc., without glare and without weight Shadow, shock and corrosion resistance, energy saving, safe and reliable.
Instructions
According to the site environment and lighting needs, determine the installation location and mode of the lamp and fix it; according to the distance from the lamp to the 220V power contact point, prepare the corresponding length of φ6~8mm cable. Press the two cover open buttons on the bottom of the lamp holder by hand, open the front cover of the lamp, and insert one end of the prepared cable into the lamp cavity through the compression nut of the introduction device. According to the polarity marked on the terminal block, connect the fire wire to “Lâ€. At the end, the neutral wire is connected to the “N†terminal. The ground wire is connected to the grounding terminal, and then the compression nut of the introduction device is tightened. Close the front cover and connect the other end of the cable to 220V to illuminate it. When replacing the bulb, press the two cover-opening buttons on the bottom of the lamp cap to open the front cover of the lamp, unscrew the bad bulb and replace it with a new one of the same type, and then fasten the front cover.
Precautions
1. When the light is transported, it should be installed in the equipped carton and be equipped with foam shock absorption.
2. When used, there is a certain temperature rise on the surface of the lamp, which is a normal phenomenon; the center temperature of the transparent part is relatively high and must not be touched.
3, when replacing the bulb, should use the same type, power bulb; if you change the bulb type or power, should replace the matching ballast.
NSC9700 anti-glare passage light is suitable for:
Applicable to roads, railway tunnels, bridges, culverts, buildings, etc. for flood lighting use.
NSC9700 Anti-glare Channel Light Performance Features:
1. Anti-glare function: Nano photocatalyst glass can be used to automatically decompose the surface stains to maintain the light transmission effect. At the same time, diffuse reflection technology and protection angle design can be used to effectively prevent glare. It can effectively reduce the stimulation to the eyes of operators and construction workers and avoid the occurrence of glare. Discomfort and fatigue. Anti glare passage lamp 250W/400W
2.Efficient light energy saving: Use a special gas discharge bulb as the light source, which has high luminous efficiency and long service life. When using double-tube HPS lamp, it can be started and restarted immediately without cooling.
3. Applicable environment: It adopts high-strength alloy material, which has strong resistance to strong collision and impact; multi-channel shockproof structure and surface spraying treatment can be stable in high-frequency vibration, humidity, and high-temperature environments in workshops, roadbeds, rails, etc. jobs.
4. Installation methods: Wall-mounting and ceiling-mounting methods are available. The irradiation angle can be arbitrarily adjusted within the range of up and down 25° as required. According to the needs of the site, it can adapt the cables with different diameters of φ10～4mm, and can realize the use of multiple lamps in parallel, which is suitable for layout engineering lighting. Electronic and mechanical double protection device, automatically cut off the power after opening the cover, the use of more secure and reliable.
Instructions
According to the site environment and lighting needs, determine the installation location and mode of the lamp and fix it; according to the distance from the lamp to the 220V power contact point, prepare the corresponding length of φ6~8mm cable. Press the two cover open buttons on the bottom of the lamp holder by hand, open the front cover of the lamp, and insert one end of the prepared cable into the lamp cavity through the compression nut of the introduction device. According to the polarity marked on the terminal block, connect the fire wire to “Lâ€. At the end, the neutral wire is connected to the “N†terminal. The ground wire is connected to the grounding terminal, and then the compression nut of the introduction device is tightened. Close the front cover and connect the other end of the cable to 220V to illuminate it. When replacing the bulb, press the two cover-opening buttons on the bottom of the lamp cap to open the front cover of the lamp, unscrew the bad bulb and replace it with a new one of the same type, and then fasten the front cover.
Precautions
1. When the light is transported, it should be installed in the equipped carton and be equipped with foam shock absorption.
2. When used, there is a certain temperature rise on the surface of the lamp, which is a normal phenomenon; the center temperature of the transparent part is relatively high and must not be touched.
3, when replacing the bulb, should use the same type, power bulb; if you change the bulb type or power, should replace the matching ballast.
NSC9700 anti-glare passage light is suitable for:
Applicable to roads, railway tunnels, bridges, culverts, buildings, etc. for flood lighting use.
NSC9700 Anti-glare Channel Light Performance Features:
1. Anti-glare function: Nano photocatalyst glass can be used to automatically decompose the surface stains to maintain the light transmission effect. At the same time, diffuse reflection technology and protection angle design can be used to effectively prevent glare. It can effectively reduce the stimulation to the eyes of operators and construction workers and avoid the occurrence of glare. Discomfort and fatigue. Anti glare passage lamp 250W/400W
2.Efficient light energy saving: Use a special gas discharge bulb as the light source, which has high luminous efficiency and long service life. When using double-tube HPS lamp, it can be started and restarted immediately without cooling.
3. Applicable environment: It adopts high-strength alloy material, which has strong resistance to strong collision and impact; multi-channel shockproof structure and surface spraying treatment can be stable in high-frequency vibration, humidity, and high-temperature environments in workshops, roadbeds, rails, etc. jobs.
4. Installation methods: Wall-mounting and ceiling-mounting methods are available. The irradiation angle can be arbitrarily adjusted within the range of up and down 25° as required. According to the needs of the site, it can adapt the cables with different diameters of φ10～4mm, and can realize the use of multiple lamps in parallel, which is suitable for layout engineering lighting. Electronic and mechanical double protection device, automatically cut off the power after opening the cover, the use of more secure and reliable.
Solar Street Light,Solar Street Lamp Post,Solar Powered Street Lamp Post,Solar Powered Parking Lot Lights
Zhongshan Tiger Lighting Co.,Ltd. , https://www.tigerstreetlight.com